| Case CX290DLC SL Hydraulic Final Drive Motor | r:0.6; SW:4 mm; C:16 mm; D:62 mm; S:9 mm; C0:11.2 kN; d1:44.1 mm; B2:15.9 mm; G:M8x1; B:23.8 mm; |
| Case 72281630 Hydraulic Final Drive Motor | C0 - Static Radial Rating:98700 N; WPD:79.2 mm; B - Cone Width:23.000 mm; Cg - Geometry Factor:0.0809; C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)2:10500 lbf; d:45.000 mm; Ca90 - Dynamic Thrust Rating (90 million revolutions)7:18700 N; a - Effective Center Location4:-4.3 mm; Cone Part Number:X32209N; C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)1:40600 lbf; |
| Case CX31B Hydraulic Final Drive Motor | Bore Size d:17 mm; Oil Limiting Speed:24000 rpm; Outside Diameter D:35.000 mm; Features:Open; Weight:0.03 Kg; Clearance:C3; Outside Ring Width B:8.000 mm; Grease Limiting Speed:17000 rpm; Cr - Dynamic Load Rating:6 kN; C0r - Static Load Rating:3.3 kN; |
| Case 161320A1 Hydraulic Final Drive Motor | B1:35.7 mm; G:R1/8"; H:42.9 mm; A:38 mm; Designation of open end cover:SCOE206-30; d1:44.1 mm; S:9 mm; A1:25 mm; Recommended tightening torque for set screw:11.5 Nm; H2:82 mm; |
| Case 16132A1 Hydraulic Final Drive Motor | C0:71.5 kN; B:96 mm; S:39.7 mm; Designation of bearing:UC218G2; Weight:4.45 kg; s1:48 mm; T max.:100 °C; Recommended tightening torque for set screw:33 Nm; d:90 mm; T min.:-20 °C; |
| Case 440 1-SPD Reman Hydraulic Final Drive Motor | Jmax:268 mm; Jmin:252 mm; H2:32.0 mm; Shaft Diameter d:75 mm; Bearing:22217K; Bolt Qty:2; Housing Mass:10.4 Kg; C1 Dynamic Load Rating:297; Cage Type:EJ; A1:90 mm; |
| Case 151754A1 Hydraulic Final Drive Motor | Nref:5,300 rpm; Min operating temperature, Tmin:-40 °C; da min:98 mm; d:85 mm; ra max:2.5 mm; Max operating temperature, Tmax:120 °C; Brand:SNR; D1:158.4 mm; Characteristic rolling element frequency, BSF:4.16 Hz; Static load, C0:96.8 kN; |
| Case 440 2-SPD Reman Hydraulic Final Drive Motor | Dimension SA:3.39 in; Y1 - Geometry Factor:2.79; Dimension M:2.15 in; Pre Install Clearance Max:0.0026 in; Float:0.083 in; Locking Style:Single Concentric; Engineering Group:Mounted Bearing; Dimension D Max:8.63 in; Pre Install Clearance Min:0.0016 in; Dimension RA:0.21 in; |
| Case 84565749R Reman Hydraulic Final Drive Motor | Max operating temperature, Tmax:110 °C; Enclosure Type:Non-Contact Seal; Nlim (grease):32,000 rpm; ra max:0.3 mm; Cage Material:Steel; Weight / Kilogram:0.012; Inner Race Width:0 Inch | 0 Millimete; D:22 mm; Internal Clearance:C2-Snug; Manufacturer Name:NTN; |
| Case CX330 Hydraulic Final Drive Motor | Surface Treatment:No; Unit, Type:Bearing unit; Rolling Element Material:Steel; Bearing Unit, Type:Pillow Type; Basic Dynamic Load Rating Cr(N):52500; Lubrication method:Oil-Free Type; Unit Body Material:Cast Iron; Cover Type:Steel plate single c; |