| Case 87035341 Reman Hydraulic Final Drive Motor | Size Standards:Metric System; Number of Raceway Ring Rows:Single Row; Bearing Style:Rubber Sealed; Type:Ball; d:15; Rolling Element Material:Steel; Basic Dynamic Load Rating(N):11400; Preload Mark:C3; Seal, Shield Symbols:LLU; |
| Case CX250DLC Hydraulic Final Drive Motor | S:6.5 mm; Z:22 mm; d1:27.2 mm; J:64 mm; e:15 mm; C0:4.78 kN; N:12mm; Recommended tightening torque for set screw:5.5 Nm; T max.:100 °C; A2:37.1 mm; |
| Case 87349721 Reman Hydraulic Final Drive Motor | T max.:100 °C; Designation of bearing:UC205G2L4; G:R1/8"; A:21 mm; T min.:-20 °C; H:78 mm; B:34 mm; C:14 kN; SW:3 mm; Designation of closed end cover:SCC205; |
| Case 160142A1 Hydraulic Final Drive Motor | C - Dynamic Load (Basic):86600 lb; Shaft Size Type:Metric; Y2 - Geometry Factor:4.17; Dimension BC:9.5 in; Grease Lubrication - B/C/O Seal:950 rpm; Dimension E:6.72 in; Shaft Size :90 mm; Housing Style:Four-Bolt Square Fla; UPC Code:0883450336987; Oil Lubrication - B/C/O Seal:1000 rpm; |
| Case 161320A1 Hydraulic Final Drive Motor | B1:35.7 mm; G:R1/8"; H:42.9 mm; A:38 mm; Designation of open end cover:SCOE206-30; d1:44.1 mm; S:9 mm; A1:25 mm; Recommended tightening torque for set screw:11.5 Nm; H2:82 mm; |
| Case 87367732R Reman Hydraulic Final Drive Motor | J:121 mm; H:90 mm; S:8 mm; Z:52.8 mm; G:M6x1; C0:11.2 kN; H2:130 mm; T min.:-20 °C; A:50 mm; B:30 mm; |
| Case CX240BLR Hydraulic Final Drive Motor | Weight / Kilogram:2.645; Min operating temperature, Tmin:-40 °C; Width:1.811 Inch | 46 Mill; Nlim (grease):4,800 rpm; UNSPSC:31171547; Retainer:Yes; Inventory:0.0; Harmonized Tariff Code:8482.50.00.00; Bore Profile:Straight; Weight / LBS:5.846; |
| Case 450 1-SPD Reman Hydraulic Final Drive Motor | f0:13.2; Min operating temperature, Tmin:-20 °C; ra max:0.3 mm; Dynamic load, C:5.1 kN; Static load, C0:2.39 kN; Characteristic rolling element frequency, BSF:4.07 Hz; Characteristic inner ring frequency, BPFI:4.93 Hz; D:28 mm; d:12 mm; Nlim (grease):26,000 rpm; |
| Case 72281630 Hydraulic Final Drive Motor | C0 - Static Radial Rating:98700 N; WPD:79.2 mm; B - Cone Width:23.000 mm; Cg - Geometry Factor:0.0809; C90(2) - Dynamic Radial Rating (Two-Row, 90 million revolutions)2:10500 lbf; d:45.000 mm; Ca90 - Dynamic Thrust Rating (90 million revolutions)7:18700 N; a - Effective Center Location4:-4.3 mm; Cone Part Number:X32209N; C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)1:40600 lbf; |
| Case CX300C Hydraulic Final Drive Motor | s1:21.45 mm; Designation of housing:C207-; H:90 mm; Designation of bearing:UC207-23G2; B:42.9 mm; Weight:0.85 kg; S:17.5 mm; SW:3.97 mm; A3:2 mm; G:M6x1; |