| Case 155817A1 Hydraulic Final Drive Motor | da max:26 mm; Product Group:B04144; Radial clearance class:C3; E:41.5 mm; B:18 mm; Minimum Buy Quantity:N/A; Fatigue limit load, Cu:3.45 kN; Mass (without HJ ring):0.14 kg; d:20 mm; Nlim (grease):14,000 rpm; |
| Case 9050B Hydraulic Final Drive Motor | Cg - Geometry Factor:0.0668; C90 - Dynamic Radial Rating (90 million revolutions)4:3180 lbf; Cup Part Number:14273; C - Cup Width:16.955 mm; G1 - Heat Generation Factor (Roller-Raceway):18; a - Effective Center Location3:-4.3 mm; C1 - Dynamic Radial Rating (1 million revolutions)5:12300 lbf; db - Cone Backface Backing Diameter:45.97 mm; Ab - Cage-Cone Frontface Clearance:1.8 mm; R - Cone Backface To Clear Radius1:3.560 mm; |
| Case 72271598 Hydraulic Final Drive Motor | G:M6x1; s1:24.6 mm; J:151.5 mm; T min.:-40 °C; Dz:95 mm; B:49.2 mm; Recommended tightening torque for set screw:11.5 Nm; Designation of bearing:UC209G2T04; A1:35 mm; S:19 mm; |
| Case CX160B Hydraulic Final Drive Motor | Fatigue limit load, Cu:2.36 kN; d:60 mm; f0:13.2; Dynamic load, C:82 kN; ra max:2 mm; Static load, C0:52 kN; da max:80.5 mm; Characteristic rolling element frequency, BSF:4.09 Hz; B:31 mm; D:130 mm; |
| Case 410 1-SPD Reman Hydraulic Final Drive Motor | Snap Ring:No; Inch - Metric:Metric; Characteristic cage frequency, FTF:0.43 Hz; Cage Material:Steel; Weight / Kilogram:0.233; Characteristic outer ring frequency, BPF0:5.55 Hz; Harmonized Tariff Code:8482.10.50.68; Inner Race Width:0 Inch | 0 Millimete; Manufacturer Name:NTN; Weight / LBS:0.53572; |
| Case CK75 Aftermarket Hydraulic Final Drive Motor | B:34 mm; da max:119 mm; da min:111 mm; Min operating temperature, Tmin:-20 °C; f0:14.4; d:100 mm; Da max:169 mm; Nref:4,800 rpm; Mass:3.19 kg; Brand:SNR; |
| Case CX290DLC MH Hydraulic Final Drive Motor | RoHS:6; Surface Treatment:No Surface Treatment; Nominal of Thread(mm):M95; Type:Shake Proof Washer; Shape:Round shape; I.D. (D1):95; Tongue:Tongue bent; Days to Ship:Same day; |
| Case 876020262 Hydraulic Final Drive Motor | Dimension G:4.2500 in; C - Dynamic Load (Basic):49900 lb; Dimension SVV:4.09 in; Oil Lubrication - T Seal:2900 rpm; Housing Style:Four-Bolt Pillow Blo; Shaft Tolerance:0.0015 in; Pre Install Clearance Min:0.0030 in; Grease Lubrication - T Seal:2400 rpm; Dimension E:2.75 in; Dimension L:4.17 in; |
| Case 440CT-3 2-SPD RH Hydraulic Final Drive Motor | Max Oil Speed:1600; L:510 mm; G:M24; J:430.00 mm; H:333 mm; Material :Cast Iron; Housing:SNT 3134; C:14 mm; N1:34 mm; Bearing:23134K; |
| Case 9010 Hydraulic Final Drive Motor | Shape:Flange Type; RoHS:6; Volume Discount:Available; Bearing Used:Deep Groove Ball Bea; Holder Surface Treatment:Not Provided; Bearing Retained:Yes (with retaining; Seals:VV (Non-Contact Rubb; Number of Bearings:Single; Bearing I.D. d(mm):8; |