| Case CX240BLR Hydraulic Final Drive Motor | Weight / Kilogram:2.645; Min operating temperature, Tmin:-40 °C; Width:1.811 Inch | 46 Mill; Nlim (grease):4,800 rpm; UNSPSC:31171547; Retainer:Yes; Inventory:0.0; Harmonized Tariff Code:8482.50.00.00; Bore Profile:Straight; Weight / LBS:5.846; |
| Case 9007B Hydraulic Final Drive Motor | T max.:100 °C; A2:33.3 mm; C0:6.65 kN; S:12.7 mm; N:12mm; s1:15.5 mm; e:15 mm; d:12 mm; Recommended tightening torque for set screw:5.5 Nm; J:90 mm; |
| Case CX290DLC SL Hydraulic Final Drive Motor | r:0.6; SW:4 mm; C:16 mm; D:62 mm; S:9 mm; C0:11.2 kN; d1:44.1 mm; B2:15.9 mm; G:M8x1; B:23.8 mm; |
| Case 450CT-3 2-SPD RH Hydraulic Final Drive Motor | J:82.5 mm; B:36.4 mm; A:33.5 mm; e:20 mm; Weight:1.23 kg; Recommended tightening torque for set screw:8 Nm; d:28.58 mm; B1:48.3 mm; A1:12 mm; Designation of housing:FE206-; |
| Case 151754A1 Hydraulic Final Drive Motor | Nref:5,300 rpm; Min operating temperature, Tmin:-40 °C; da min:98 mm; d:85 mm; ra max:2.5 mm; Max operating temperature, Tmax:120 °C; Brand:SNR; D1:158.4 mm; Characteristic rolling element frequency, BSF:4.16 Hz; Static load, C0:96.8 kN; |
| Case CX290B Hydraulic Final Drive Motor | da min:65 mm; rs min:1 mm; Lubrication hole on inner ring:Non/No; F:70 mm; d:60 mm; B:60 mm; Mass:0.46 kg; Brand:NTN; Precision class:P0; ras max:1 mm; |
| Case CX250DLC LR Hydraulic Final Drive Motor | T min.:-40 °C; L:61 mm; Designation of bearing:ES204G2T04; H:112 mm; T max.:100 °C; Designation of housing:FLE204N-; Weight:0.49 kg; Z:50.8 mm; C:12.8 kN; d1:32.4 mm; |
| Case 160142A1 Hydraulic Final Drive Motor | C - Dynamic Load (Basic):86600 lb; Shaft Size Type:Metric; Y2 - Geometry Factor:4.17; Dimension BC:9.5 in; Grease Lubrication - B/C/O Seal:950 rpm; Dimension E:6.72 in; Shaft Size :90 mm; Housing Style:Four-Bolt Square Fla; UPC Code:0883450336987; Oil Lubrication - B/C/O Seal:1000 rpm; |
| Case 36B Hydraulic Final Drive Motor | d:6 mm; Mass:0.006 kg; Min operating temperature, Tmin:-25 °C; Nlim (oil):42,000 rpm; Fatigue limit load, Cu:0.04 kN; D:17 mm; Static load, C0:0.86 kN; B:6 mm; Max operating temperature, Tmax:120 °C; Dynamic load, C:2.19 kN; |
| Case 450 1-SPD Reman Hydraulic Final Drive Motor | f0:13.2; Min operating temperature, Tmin:-20 °C; ra max:0.3 mm; Dynamic load, C:5.1 kN; Static load, C0:2.39 kN; Characteristic rolling element frequency, BSF:4.07 Hz; Characteristic inner ring frequency, BPFI:4.93 Hz; D:28 mm; d:12 mm; Nlim (grease):26,000 rpm; |