| Case 87367732R Reman Hydraulic Final Drive Motor | J:121 mm; H:90 mm; S:8 mm; Z:52.8 mm; G:M6x1; C0:11.2 kN; H2:130 mm; T min.:-20 °C; A:50 mm; B:30 mm; |
| Case 9010B Hydraulic Final Drive Motor | r - Cup Backface To Clear Radius1:0.030 in; Y - ISO Factor3:1.96; Series:3500; Db - Cup Backface Backing Diameter:3.03 in; D:3.4375 in; Design Units:Imperial; Da - Cup Frontface Backing Diameter:3.23 in; e - ISO Factor2:0.31; Cg - Geometry Factor:0.0808; Cup Part Number:3526; |
| Case CX230 Hydraulic Final Drive Motor | Days to Ship:8 Days; Stroke:No; Basic Load Rating, Static Rating(N):45000; Seal:Silicone; d:55; Accessory:With steel plate cov; Fit:J7; Basic Load Rating, Dynamic Rating(N):71600; Surface Treatment:No; Rolling Element Material:Bearing Steel; |
| Case CX240B Hydraulic Final Drive Motor | Bearing Type:Split Cylindrical Re; Support Type:Round Flange; Dimension R:13.1 in; Bolt Size:4 x M16; Ca - Axial Load Rating:4181.39 lbf; Dimension P:0.9 in; Cor - Static Load Rating:95993 lbf; Dimension H:3.6 in; Bearing UPC:013992026712; Shaft Size:4.25 in; |
| Case CX225SR Hydraulic Final Drive Motor | A:30 mm; H1:9 mm; Recommended tightening torque for set screw:3.5 Nm; L1:17.5 mm; C:9.55 kN; L:63 mm; G:M6x1; Designation of housing:PAE203N-; C0:4.78 kN; d:15 mm; |
| Case CX290DLC MH Hydraulic Final Drive Motor | RoHS:6; Surface Treatment:No Surface Treatment; Nominal of Thread(mm):M95; Type:Shake Proof Washer; Shape:Round shape; I.D. (D1):95; Tongue:Tongue bent; Days to Ship:Same day; |
| Case 87035344 Reman Hydraulic Final Drive Motor | Bearing Used:Deep Groove Ball Bea; Flange Shape:Round Type; Bearing Part Number:6000; Days to Ship:7 Days; Type:Bearings with Housin; Flange O.D. H(φ):52; Bearing Material:[Steel] Steel; Bearing Retained:No; Holder Surface Treatment:Clear Anodize; |
| Case 9020 Hydraulic Final Drive Motor | Type:Bearings with Housin; Flange Shape:Round Type; Bearing Retained:No; Seals:DD (Contact Rubber S; Bearing I.D. d(mm):20; Width T(mm):30 ～ 70; Number of Bearings:Double; Bearing Used:Deep Groove Ball Bea; RoHS:6; |
| Case 9030 Hydraulic Final Drive Motor | Bearing Retained:No; Shape:T-Shaped; T(mm):25 ～ 35; Holder Surface Treatment:Black Oxide Coating; Housing Material:1045 Carbon Steel; Bearing Material:[Steel] Steel; Bearing Used:Deep Groove Ball Bea; Bearing Part Number:608; Number of Bearings:Double; |
| Case 87045010 Reman Hydraulic Final Drive Motor | Features:Non-Contact Seals; Outside Ring Width B:5.000 mm; Bore Size d:3.000 mm; Outside Diameter D:13.000 mm; Weight:0.0030 Kg; Oil Limiting Speed:60000 rpm; Grease Limiting Speed:51000 rpm; Cr - Dynamic Load Rating:1.3 kN; Radius Rs min:0.200 mm; C0r - Static Load Rating:0.49 kN; |