| 39 0541 01 Rollix Slewing Ring Bearings | da max.:48.8 mm; Da max.:73 mm; Fatigue load limit Pu:0.8 kN; Basic static load rating C0:19 kN; r1,2 min.:1.1 mm; Basic dynamic load rating C:32.5 kN; ra max.:1 mm; D:80 mm; da min.:47 mm; Mass bearing:0.36 kg; D2 ≈:71.5 mm; Calculation factor f0:13.8; B:18 mm; Limiting speed:5600 r/min; d:40 mm; Calculation factor kr:0.025; d2 ≈:49.146 mm; |
| 192.32.3150.990.41.1502 Standard 5 Slewing Ring Bearings | Basic dynamic load rating C:490 kN; rb max.:1 mm; r2 min.:1 mm; Basic static load rating C0:2450 kN; Lubricant:Regular relubricatio; Mass plain bearing:2.75 kg; r1 min.:1 mm; Da min.:112.9 mm; D:130 mm; Material constant KM:330; d:90 mm; B:60 mm; Da max.:123.5 mm; b:9.5 mm; ra max.:1 mm; Specific static load factor K0:500 N/mm²; da min.:97.4 mm; Specific dynamic load factor K:100 N/mm²; α:5 °; |
| 6 0734 Rollix Slewing Ring Bearings | Reference speed:480 r/min; d:670 mm; D:800 mm; da min.:744 mm; d1 ≈:795 mm; Mass bearing (including seat washer where applicable):74 kg; Minimum load factor A:90; H:78 mm; Da max.:726 mm; ra max.:3 mm; Limiting speed:670 r/min; Basic static load rating C0:4150 kN; D1 ≈:675 mm; Fatigue load limit Pu:57 kN; r1,2 min.:4 mm; Basic dynamic load rating C:540 kN; |
| 8 0574 08 Rollix Slewing Ring Bearings | P90°:36 kN; P180°:23.1 kN; J1:53.975 mm; End plug (suffix Y):EPR 8; PG:1/8 NPT; H2:31.75 mm; R1:53.181 mm; h:31.75 mm; A2:209.55 mm; A1:88.9 mm; Max. speed for Taconite seal:1150 r/min; S:4.763 mm; Taconite seal:TER 43; Cap bolt recommended tightening torque:149.1 N·m; H1:88.9 mm; Mass pillow block:17.4 kg; ba:34.131 mm; Initial grease fill:87.885 g; N1:19.05 mm; H:169.863 mm; |
| 121.36.4250.990.41.1502 Standard 5 Slewing Ring Bearings | d:5 mm; Permissible sliding velocity v min.:0.25 m/s; Coefficient of friction µ max.:0.1; Specific static load factor K0:20 N/mm²; D:10 mm; Coefficient of friction µ min.:0.05; Mass bushing:0.002 kg; Tolerance housing:H7; Tolerance shaft:h8; Specific dynamic load factor K:10 N/mm²; B:6 mm; Permissible sliding velocity v max.:5 m/s; |
| 2 105 Rollix Slewing Ring Bearings | Calculation factor Y:1.8; Db min.:90 mm; T:27 mm; B:27 mm; Da min.:85 mm; C:21 mm; d1 ≈:77.2 mm; Basic static load rating C0:143 kN; Calculation factor Y0:1; Calculation factor e:0.33; ra max.:1.5 mm; rb max.:1.5 mm; Cb min.:6 mm; Mass bearing:0.7 kg; D:95 mm; r1,2 min.:1.5 mm; Limiting speed:6700 r/min; Reference speed:5300 r/min; Fatigue load limit Pu:16 kN; Basic dynamic load rating C:113 kN; |
| 8 04 Rollix Slewing Ring Bearings | Mass bushing:0.036 kg; Coefficient of friction µ min.:0.05; Specific static load factor K0:20 N/mm²; Tolerance housing:H7; Tolerance shaft:h8; Permissible sliding velocity v min.:0.25 m/s; Permissible sliding velocity v max.:5 m/s; Coefficient of friction µ max.:0.1; d:25 mm; B:25 mm; D:30 mm; Specific dynamic load factor K:10 N/mm²; |
| 161.45.2510.890.11.1503 Standard 5 Slewing Ring Bearings | Grease:7 900 min-1; Static (Cor):24.170 kN; rs:1.5 mm; Oil:9 400 min-1; Weight:0.625 kg; d:40 mm; da:47 min; Da:81 max; ra:1.5 max; Pu:1.099 kN; Bearing designation:6308 ; Dynamic (Cr):40.760 kN; D:90 mm; B:23 mm; |
| 192.40.3550.990.41.1502 Standard 5 Slewing Ring Bearings | r1,2 min.:3.3 mm; Calculation factor Y2:3; d1 ≈:622 mm; D1 ≈:720 mm; Design variant/feature:TQOT; r3,4 min.:6.4 mm; D:812.8 mm; Fatigue load limit Pu:2400 kN; Comparative radial load rating CF:3550 kN; Calculation factor Y1:2; d:571.5 mm; B:593.725 mm; Comparative axial load rating CFa:580 kN; Calculation factor e:0.33; Calculation factor Y0:2; T:593.725 mm; Thrust factor K:1.76; Mass bearing:1105 kg; |
| 36 0841 01 Rollix Slewing Ring Bearings | Oil Speed Rating n2:6000 rpm; Grease Speed Rating Open/Shielded n1:5000 rpm; Sealed Speed Rating n3:3400 rpm; Basic Dynamic Radial Load Rating C:81900 N; d:60.000 mm; Accessories:Without Accessories; B:31.00 mm; Grease Speed Rating n1:5000 rpm; Fillet Radius ra:2.00 mm; Basic Static Radial Load Rating Co:52000 N; Oil Speed Rating Open/Shielded n2:6000 rpm; D:130.0000 mm; |