| 8 04 Rollix Slewing Ring Bearings | Mass bushing:0.036 kg; Coefficient of friction µ min.:0.05; Specific static load factor K0:20 N/mm²; Tolerance housing:H7; Tolerance shaft:h8; Permissible sliding velocity v min.:0.25 m/s; Permissible sliding velocity v max.:5 m/s; Coefficient of friction µ max.:0.1; d:25 mm; B:25 mm; D:30 mm; Specific dynamic load factor K:10 N/mm²; |
| 121.45.5300.990.41.1502 Standard 5 Slewing Ring Bearings | R1:163.512 mm; J min.:666.75 mm; Housing:SAFS 640; Ca:147.803 mm; Labyrinth ring:2 x LOR 664; H:495.3 mm; h:87.313 mm; A1:228.6 mm; Stabilizing ring:SR-0-40; J1:139.7 mm; Cap bolt, SAE grade:8; P150°:222 kN; RG:1 NPT; Bearing limiting speed:1500 r/min; Mass pillow block:431 kg; P90°:400 kN; ba:103.188 mm; Cap bolt recommended tightening torque:4284.4 N·m; End plug (suffix Y):EPR 21; |
| 36 0741 01 Rollix Slewing Ring Bearings | Basic dynamic load rating C:486 kN; Calculation factor Y1:0.81; K:10 mm; r3,4 min.:3 mm; Reference speed:1900 r/min; Da min.:151 mm; Basic static load rating C0:630 kN; T:93 mm; d:90 mm; r5 min.:1 mm; Limiting speed:3400 r/min; Calculation factor e:0.83; Da max.:177.5 mm; Fatigue load limit Pu:71 kN; da max.:110 mm; 2B:86 mm; Calculation factor Y2:1.2; rc max.:1 mm; ra max.:3 mm; Calculation factor Y0:0.8; |
| 92.50.2644.990.41.1502 Standard 5 Slewing Ring Bearings | P180°:42.3 kN; H:192.088 mm; P120°:38.3 kN; h:42.862 mm; ba:35.719 mm; Cap bolt, SAE grade:8; Da:160 mm; Initial grease fill:286.33 g; Taconite seal:TER 36; Ca:64.795 mm; Mass pillow block:21.5 kg; H1:101.6 mm; Cap bolt recommended tightening torque:298.3 N·m; Cap bolt:2 x 5/8-11 UNC; Appropriate attachment bolt size G:0.625 in; P90°:60.9 kN; P150°:34.7 kN; L:349.25 mm; P60°:101 kN; |
| 38 0941 01 Rollix Slewing Ring Bearings | B:20 mm; D:17 mm; Specific dynamic load factor K:40 N/mm²; Coefficient of friction µ max.:0.15; d:15 mm; Specific static load factor K0:80 N/mm²; Permissible sliding velocity v min.:0 m/s; Permissible sliding velocity v max.:1 m/s; Tolerance housing:H7; Mass bushing:0.0015 kg; Coefficient of friction µ min.:0.06; Tolerance shaft:h9; |
| 39 0641 01 Rollix Slewing Ring Bearings | Basic dynamic load rating C:1120 kN; Da max.:965 mm; d:900 mm; D1 ≈:906 mm; Basic static load rating C0:10400 kN; ra max.:4 mm; r1,2 min.:5 mm; D:1060 mm; Reference speed:300 r/min; Minimum load factor A:610; d1 ≈:1054 mm; da min.:995 mm; H:130 mm; Mass bearing (including seat washer where applicable):205 kg; Fatigue load limit Pu:125 kN; Limiting speed:430 r/min; |
| 6 0508 Rollix Slewing Ring Bearings | dk:53 mm; Specific dynamic load factor K:100 N/mm²; C1 max.:24 mm; h1:145 mm; α:6 °; G:M 42x3; d2 max.:94 mm; Material constant KM:330; B:28 mm; l4 max.:194 mm; Basic static load rating C0:166 kN; d:40 mm; w:50 mm; Mass rod end:2.2 kg; r1 min.:0.6 mm; l3 min.:65 mm; d4 ≈:58 mm; Basic dynamic load rating C:100 kN; l5 ≈:25 mm; l7 min.:40 mm; |
| 11.35.2620.000.11.1503 Standard 5 Slewing Ring Bearings | Mass needle roller:0.108 g; r1,2 min.:0.1 mm; r1 max.:0.4 mm; Dw:1.5 mm; Lw:7.8 mm; r2 max.:0.6 mm; |
| 11.50.3167.001.49.1502 Standard 5 Slewing Ring Bearings | Recommended lock nut tightening angle α:95 °; Fatigue load limit Pu:0.475 kN; Recommended diameter for attachment bolts, mm G:10 mm; Mass bearing unit:1.05 kg; R1:19.5 mm; RG:1/4-28 UNF; SWN:7 mm; J6:96 mm; B1:38 mm; N4:4 mm; Recommended diameter for attachment bolts, inch G:0.375 in; d:25 mm; Basic dynamic load rating C:19.5 kN; J7:24.5 mm; GN:1/4-28 SAE-LT; Bearing:YSA 206-2FK; J:83 mm; Db1:76 mm; |
| 29 1091 01 Rollix Slewing Ring Bearings | Oil level, max.:104 mm; Oil seal:2 x TSD 3068 U; Cap bolt, rec. tightening torque:400 N·m; Q150°:1650 kN; N:50 mm; Ca:197 mm; N1:42 mm; Cap bolt, size:M 30x220; H:631 mm; P150°:2200 kN; A2:363 mm; A:363 mm; N4 max.:25 mm; H1:320 mm; Appropriate attachment bolt, size G:36 mm; L:880 mm; P180°:2800 kN; Da:520 mm; P90°:3400 kN; Appropriate attachment bolt, rec. tightening torque:2280 N·m; |